123 lines
3.1 KiB
Markdown
123 lines
3.1 KiB
Markdown
# HannaBox
|
|
|
|
## Microcontroller
|
|
|
|
We are using an ESP-WROOM-32 module. For the mp3 decoding we need a multicore CPU, be careful, there are some ESP32 with only one core.
|
|
|
|
|
|
|
|
## Pins
|
|
|
|
The plain number refers to the GPIO pin.
|
|
|
|
### Amplifier
|
|
|
|
MAX98357A I2S 3W DAC Class D Amplifier Module
|
|
|
|
|
|
|
|
|
|
SD / MODE
|
|
|
|
This pin is used for shutdown mode but is also used for setting which channel is output. It's a little confusing but essentially:
|
|
|
|
If SD is connected to ground directly (voltage is under 0.16V) then the amp is shut down
|
|
If the voltage on SD is between 0.16V and 0.77V then the output is (Left + Right)/2, that is the stereo average.
|
|
If the voltage on SD is between 0.77V and 1.4V then the output is just the Right channel
|
|
If the voltage on SD is higher than 1.4V then the output is the Left channel.
|
|
|
|
This is compounded by an internal 100K pulldown resistor on SD so you need to use a pullup resistor on SD to balance out the 100K internal pulldown.
|
|
|
|
For the breakout board, there's a 1Mohm resistor from SD to Vin which, when powering from 5V will give you the 'stereo average' output. If you want left or right channel only, or if you are powering from non-5V power, you may need to experiment with different resistors to get the desired voltage on SD
|
|
|
|
```
|
|
26 -> DIN
|
|
27 -> BCLK
|
|
25 -> LRC
|
|
5V -> Vin
|
|
GND -> GND
|
|
```
|
|
|
|
### SD Card Reader
|
|
|
|
SD Card Reader Adapter Modul
|
|
|
|
```
|
|
CS -> 22 (D1)
|
|
MOSI -> 23 (D7)
|
|
CLK -> 18 (D5)
|
|
MISO -> 19 (D6)
|
|
```
|
|
|
|
Or if a plain reader is used:
|
|
|
|
|
|
|
|
|
|
### RFID Reader
|
|
|
|
NFC RFID module RC522
|
|
|
|
```
|
|
SOA -> 32
|
|
SCK -> 18
|
|
MOSI -> 23
|
|
MISO -> 19
|
|
IRQ -> NC
|
|
GND -> GND
|
|
RST -> 33
|
|
3.3V -> 3.3V
|
|
|
|
```
|
|
|
|
#### RFID Chip Registers
|
|
|
|
Interrupt method was not working because it seems reading a card does not trigger one.
|
|
|
|
See https://arduino.stackexchange.com/a/76285 and https://github.com/miguelbalboa/rfid/blob/master/examples/MinimalInterrupt/MinimalInterrupt.ino
|
|
|
|
|
|
### Buttons
|
|
|
|
```
|
|
Start / Stop -> 17 and GND
|
|
Wake up / Next -> 04 and GND
|
|
Previous -> 16 and GND
|
|
```
|
|
|
|
|
|
## Battery Voltage
|
|
|
|
The battery voltage is measured by the ADC of pin 35. A voltage divider halves the voltage so that the pin can not be overloaded (max 3.3V).
|
|
The voltage divider consists of two 100kOHM resistors, the voltage is measured between them. One side is connected to the battery and the other to ground.
|
|
There are 2 ADCs, make sure to not use the one which is not usable during WIFI!
|
|
|
|
## Power
|
|
|
|
We use the voltage regulator of the SD Card module. We also can use a LDL1117S33R Low Dropout Voltage regulator. For Loading the LiIon we can use a LTC4054 or a dedicated module.
|
|
|
|
|
|
## System sounds
|
|
|
|
Place these sounds in the folder `system` on the SD card:
|
|
|
|
* sleep.mp3
|
|
* start.mp3
|
|
|
|
sleep.mp3 will be played just before the timed shutdown, start.mp3 will be played if the box started and initialized successfully.
|
|
|
|
## TODOs
|
|
|
|
## Schematic without modules
|
|
|
|
### Charging circuit
|
|
|
|
https://ww1.microchip.com/downloads/en/AppNotes/01149c.pdf
|
|
MCP73837 ?
|
|
|
|
## Links
|
|
|
|
https://github.com/earlephilhower/ESP8266Audio
|
|
|
|
[Running two SPI devices at once](https://randomnerdtutorials.com/esp32-spi-communication-arduino/)
|